Wireline Sonic Waveform Data
IODP-USIO logging contractor: LDEO-BRG
Hole: U1326D
Expedition: 311
Location: Cascadia Margin (NE Pacific)
Latitude: 48° 37.630' N
Longitude: 127° 3.03' W
Logging date: October 26-27, 2005
Sea floor depth (drillers'): 1839.6 mbrf
Sea floor depth (step in GR log): 1837 mbrf
Total penetration: 300 mbsf
Total core recovered: 121.96 m (63.3 % of cored section)
Oldest sediment cored: Presumably Pleistocene - no diatoms found in the lower part of the hole
Lithologies: Clay and silty clay, with some sandy intervals
TOOL USED: DSI (Dipole Sonic Imager)
Recording mode: Monopole P&S, Cross-Dipole, Upper and Lower Dipole, and Stoneley mode.
Remarks about the recording: none.
MONOPOLE P&S MODE: measures compressional and hard-rock shear slowness. The monopole transmitter is excited by a high-frequency pulse, which reproduces conditions similar to previous sonic tools.
UPPER DIPOLE MODE: measures shear wave slowness using firings of the upper dipole transmitter.
LOWER DIPOLE MODE: measures shear wave slowness using firings of the lower dipole transmitter.
thus allowing acquisition of orthogonally polarized data for anisotropy studies.
STONELEY MODE: measures low-frequency Stoneley wave slowness. The monopole transmitter, driven by a low-frequency pulse, generates the Stoneley wave.
Acoustic data are recorded in DLIS format. Each of the eight waveforms generally consists of 512 samples (256 in cross-dipole mode), each recorded every 10 (monopole P&S) and 40 microsec (all dipole modes), at depth intervals of 15.24 cm (6 inches). The original data in DLIS format is first loaded on a Sun system using GeoFrame software. The packed waveform data files are then converted into ASCII and finally binary format.
Each line is composed of the entire waveform set recorded at each depth, preceded by the depth (multiplied by 10 to be stored as an integer). In the general case of 8 waveforms with 512 samples per waveform, this corresponds to 1 + 4x512 = 4097 columns. In this hole, the specifications of the files are:
Number of columns: 4097
Number of rows: 1553 (Pass 1)
Number of rows: 2325 (Pass 2)
All values are stored as 'signed short integers' (= 16 bits signed).
Each file can be viewed directly as an image with Spyglass transform or NIH image on MAcs and PCs, or Fortner transform or Khoros on UNIX) - where it has to be opened as either 'raw' or 'binary matrix'. Any image or signal-processing package should also allow viewing it.
The following files have been loaded:
DSI from DIT/DSI/SGT (Pass 1, open hole)
U1326D-mono_p1.bin: 1903.01-2139.54 mbrf
U1326D-ldip_p1.bin: 1903.01-2139.54 mbrf
U1326D-udip_p1.bin: 1903.01-2139.54 mbrf
U1326D-st_p1.bin: 1903.01-2139.54 mbrf
DSI from DIT/DSI/SGT (Pass 2, BHA at ~1895 mbrf)
U1326D-mono_p2.bin: 1785.21-2139.39 mbrf
U1326D-ldip_p2.bin: 1785.21-2139.39 mbrf
U1326D-udip_p2.bin: 1785.21-2139.39 mbrf
U1326D-st_p2.bin: 1785.21-2139.39 mbrf
The sonic waveform files are not depth shifted to a reference run or to the seafloor. For depth shift to the sea floor, please refer to the DEPTH SHIFT section in the standard log documentation file.
NOTE: For users interested in reading and converting the data to a format more suitable for their own purpose, the fortran declaration used to open the file *.bin would be:
open (1, file = *.bin,access = 'direct', recl = 2*(1+nwav*nsamples))
where nwav is the number of waveforms (4 or 8) and nsamples the number of samples per waveforms (see above).
If the total number of depths where waveforms have been recorded is ndepth (for a 150 m interval with data every 15cm, ndepth would be 1000), a generic loop to read the data would be
do k = 1, ndepth
...
read(1, rec=k) iz, (data(i), i = 1, nwav*nsamples)
z(k)=float(iz)/10
...
enddo
In such a case, the file dimensions will be ndepth rows by nwav*nsamples+1 columns
For further information about the logs please contact:
Cristina Broglia
Phone: 845-365-8343
Fax: 845-365-3182
E-mail: Cristina Broglia
Gilles Guerin
Phone: 845-365-8671
Fax: 845-365-3182
E-mail: Gilles Guerin