Wireline Sonic Waveform Data
IODP logging contractor: USIO/LDEO
Hole: U1338B
Expedition: 321
Location: Equatorial Pacific Sediment Mound (NE Equatorial Pacific)
Latitude: 2° 30.4692 ' N
Longitude: 117° 58.1736 ' W
Logging date: June 9-11, 2009
Sea floor depth (driller's): 4209.9 m DRF
Sea floor depth (logger's): 4207.5 m WRF (DIT/HLDS/GPIT/HNGS downlog)
Sea floor depth (logger's): 4207.5 m WRF (VSI/SGT uplog)
Sea floor depth (logger's): 4208.7 m WRF (FMS/DSI/GPIT/HNGS pass 2)
Total penetration: 416.1 m DSF
Total core recovered: 417.34 m (101 % of cored section)
Oldest sediment recovered: Lower Miocene
Lithologies: Carbonate muds, nannofossil oozes, diatom oozes, laminated and bioturbated muds.
TOOL USED: DSI
(Dipole Sonic Imager)
Recording mode:
Monopole P&S (standard frequency) and Upper Dipole (low frequency) in Pass 1 and in the downlog; Monopole P&S (low frequency) and Upper Dipole (standard frequency) in Pass 2.
Remarks about
the recording: none.
MONOPOLE P&S
MODE: measures compressional and hard-rock shear slowness. The monopole
transmitter is excited by a high-frequency pulse, which reproduces conditions
similar to previous sonic tools.
UPPER DIPOLE
MODE: measures shear wave slowness using firings of the upper dipole
transmitter.
LOWER DIPOLE
MODE: measures shear wave slowness using firings of the lower dipole
transmitter.
Acoustic
data are recorded in DLIS format. Each of the eight waveforms generally
consists of 512 samples (256 in cross-dipole mode), each recorded every 10
(monopole P&S) and 40 microsec (all dipole and Stoneley modes), at depth
intervals of 15.24 cm (6 inches). The original data in DLIS format is first
loaded on a Sun system using GeoFrame software. The packed waveform data files
are then converted into ASCII and finally binary format.
Each
row of the binary file is composed of the entire waveform set recorded at each depth, preceded by
the depth. In the general case of
8 waveforms with 512 samples per waveform, this corresponds to 1 + 4x512 = 4097
columns. In this hole, the specifications of the files are:
Number of
columns: 4097
Number of
rows: 3106 (downlog)
Number of rows: 1526
(pass 1)
Number of
rows: 2825 (pass 2)
All values are
stored as 'IEEE floating point numbers' (= 4 bytes).
Any numerical software or programing language (matlab, python,...) can import the files for further analysis of the waveforms.
The following files were converted:
DSI from FMS/DSI/GPIT/HNGS (Downlog, pipe at ~4352.5 m WRF
321-U1338B_udip_d.bin: 4155.948-4629.15 m WRF
DSI from
FMS/DSI/GPIT/HNGS (Pass 1, open hole)
321-U1338B_mono_p1.bin: 4626.86-4394.45 m WRF
321-U1338B_udip_p1.bin: 4626.86-4394.45 m WRF
DSI from
FMS/DSI/GPIT/HNGS (Pass 2, pipe at ~4348 m WRF)
321-U1338B_mono_p1.bin: 4629.15-4198.74 m WRF
321-U1338B_udip_p1.bin: 4629.15-4198.74 m WRF
The sonic
waveform files are not depth shifted to a reference run or to the seafloor. For
depth shift to the sea floor, please refer to the DEPTH SHIFT section in the
standard data processing documentation file.
NOTE: For users interested in converting the data to a format more suitable for their own purpose, a simple routine to read the binary files would include a couple of basic steps (here in old fashioned fortran 77, but would be similar in matlab or other languages):
The first step is to extract the files dimensions and specification from the header, which is the first record in each file:
open (1, file = *.bin,access = 'direct', recl = 50) <-- NB:50 is enough to real all fields
read (1, rec = 1)nz, ns, nrec, ntool, mode, dz, scale, dt
close (1)
The various fields in the header are:
- number of depths
- number of samples per waveform and per receiver
- number of receivers
- tool number (0 = DSI; 1 = SonicVISION; 2 = SonicScope; 3 = Sonic Scanner; 4 = XBAT; 5 = MCS; 6 = SDT; 7 = LSS; 8 = SST; 9 = BHC; 10 = QL40; 11 = 2PSA)
- mode (1 = Lower Dipole, 2 = Upper Dipole, 3 = Stoneley, 4 = Monopole)
- vertical sampling interval *
- scaling factor for depth (1.0 = meters; 0.3048 = feet) *
- waveform sampling rate in microseconds *
All those values are stored as 4 bytes integers, except for the ones marked by an asterisk, stored as 4 bytes IEEE floating point numbers.
Then, if the number of depths, samples per waveform/receiver, and receivers are nz, ns, and nrec, respectively, a command to open the file would be:
open (1, file = *.bin, access = 'direct', recl = 4*(1 + nrec*ns))
Finally, a generic loop to read the data and store them in an array of dimension nrec × ns × nz would be:
do k = 1, nz
read (1, rec = 1+k) depth(k), ((data(i,j,k), j = 1,ns), i = 1,nrec)
enddo
Additional
information about the drilling and logging operations can be found in the
Operations and Downhole Measurements sections of the expedition report,
Proceedings of the Integrated Drilling Program, Expedition .
For further questions about the logs, please contact:
Cristina Broglia
Phone: 845-365-8343
Fax: 845-365-3182
E-mail: Cristina Broglia
Tanzhuo Liu
Phone: 845-365-8630
Fax: 845-365-3182
E-mail: Tanzhuo Liu