FMS
Image Data Processing
IODP logging contractor: USIO/LDEO
Hole: U1376A
Expedition: 330
Location: Louisville Sea Mount (Central S Pacific Ocean)
Latitude: 32° 12.99' S
Longitude: 171° 52.84 ' W
Logging date: February 2-3, 2011
Sea floor depth (driller's): 1514.3 m DRF
Sea floor depth (logger's): 1513.5 m WRF (DIT/APS/HLDS/HNGS main run)
Total penetration: 1697.1 m DRF (m 182.8 DSF)
Total core recovered: 136.17 m (74 % of cored section)
Oldest sediment recovered: Late Cretaceous
Lithologies: Volcanic sediments, bounstone, basaltic breccia, pillow lava and massive flows
FMS Main:
FMS Repeat: 90 - 182 m WMSF
Magnetic declination: 17.9362°
The
FMS (Formation MicroScanner) maps the conductivity of the borehole wall with a
dense array of sensors. This provides a high resolution electrical image of the
formation which can be displayed in either gray or color scale. The purpose of
this report is to describe the images from IODP Expedition 330 and the steps
used to generate them from the raw FMS measurements.
The FMS tool
records electrical images using four pads, each with an array of 16 buttons,
which are pressed against the borehole wall. The tool provides approximately
25% coverage of the borehole wall in a 10-inch diameter borehole. The tool
string also contains a triaxial accelerometer and three flux-gate magnetometers
(in the GPIT, General Purpose Inclinometry Tool) whose results are used to accurately
orient and position the images. Measurements of hole size, cable speed, and
natural gamma ray intensity also contribute to the processing.
Data
Quality
Excellent borehole images were obtained due to the good hole condition (<12") and heave-compensated small downhole motion (< +/-0.5 m) of the FMS tool string.
The sea state was relatively high with a peak-to-peak heave of 0.5-1 m, so the wireline heave compensator was used during the logging operation.
Image
Processing
Processing
is required to convert the electrical current in the formation, emitted by the
FMS button electrodes, into a gray or color-scale image representative of the
conductivity changes. This is achieved through two main processing phases: data
restoration and image display.
1)
Data Restoration
Speed
Correction
The
data from the z-axis accelerometer is used to correct the vertical position of
the data for variations in the speed of the tool ('GPIT speed correction'),
including 'stick and slip'. In addition, 'image-based speed correction' is also
applied to the data: the principle behind this is that if the GPIT speed
correction is successful, the readings from the two rows of buttons on the pads
will line up, and if not, they will be offset from each other (a zigzag effect
on the image).
Equalization
Equalization is the
process whereby the average response of all the buttons of the tool are
rendered approximately the same over large intervals, to correct for various
tool and borehole effects which affect individual buttons differently. These
effects include differences in the gain and offset of the pre-amplification
circuits associated with each button, and differences in contact with the
borehole wall between buttons on a pad, and between pads.
Button Correction
If the measurements
from a button are unreasonably different from its neighbors (e.g. 'dead
buttons') over a particular interval, they are declared faulty, and the
defective trace is replaced by traces from adjacent good buttons.
EMEX Voltage
Correction.
The button response
(current) is controlled by the EMEX voltage, which is applied between the
button electrode and the return electrode. The EMEX voltage is regulated to
keep the current response within the operating range. The button current
response is divided by the EMEX voltage to give the relative conductivity of
the formation.
Depth-shifting
Each
of the logging runs is 'depth-matched' to a common scale by means of lining up
distinctive features of the natural gamma log from each of the tool strings. If
the reference logging run is not the FMS tool string, the depth shifts
determined during the standard data processing are applied to the FMS images.
The position of data located between picks is computed by linear interpolation.
Often, for short logged intervals, a single 'block shift' is sufficient to
depth-match the FMS data to the reference log.
A high-resolution conductivity log is then produced from the FMS
data by averaging the conductivity values from the 64 button electrodes. This
enables the FMS data to be plotted using common graphing applications and more
easily used in numerical analyses (e.g. spectral analysis). Specifically, the
FMS conductivity values are averaged over each of the four pads and over five
0.254-cm depth levels to produce a file with 1.27-cm sample interval containing
the total (4-pad, 64-button) average conductivity value, plus the 16-button
averages from each of the four pads. Note that the conductivity values are
un-scaled and more accurate (but lower vertical resolution) values are given by
the resistivity logs from the DIT and DLL resistivity tools.
2)
Image Display
Normalization
Once
the data is processed, both 'static' and 'dynamic' images are generated; the
differences between these two types of image are explained below. Both types
are provided online.
In 'static
normalization', a histogram equalization technique is used to obtain the
maximum quality image. In this technique, the resistivity range of the entire
interval of good data is computed and partitioned into 256 color levels. This type
of normalization is best suited for large-scale resistivity variations.
The image can be enhanced when it is
desirable to highlight features in sections of the well where resistivity
events are relatively subdued when compared with the overall resistivity range
in the section. This enhancement is called 'dynamic normalization'.
By rescaling the color intensity over a smaller interval, the contrast between
adjacent resistivity levels is enhanced. It is important to note that with
dynamic normalization, resistivities in two distant sections of the hole cannot
be directly compared with each other. A 2-m normalization interval is used.
Oriented
Presentation
The
image is displayed as an unwrapped borehole cylinder. Several passes can be
oriented and merged together on the same presentation to give additional
borehole coverage if the tool pads followed a different track. A dipping plane
in the borehole will be displayed as a sinusoid on the image; the amplitude of
this sinusoid is proportional to the dip of the plane. The images are oriented
with respect to north; hence the strike of dipping features can also be
determined.
Interested scientists are welcome to visit the log
interpretation center at LDEO if they wish to use the
image generation and interpretation software.
Additional information about the drilling and logging operations can be found in the Operations and Downhole Measurements sections of the expedition report, Proceedings of the Integrated Ocean Drilling Program, Expedition 330. For further questions about the logs, please contact:
Tanzhuo Liu
Phone: 845-365-8630
Fax: 845-365-3182
E-mail: Tanzhuo Liu
Cristina Broglia
Phone: 845-365-8343
Fax: 845-365-3182
E-mail: Cristina Broglia