FMS Image Data Processing


Science operator: Texas A&M University

Hole: U1499B

Expedition: 367

Location: China Sea Rifted Margin (South China Sea)

Latitude: 18° 27.5705' N

Longitude: 115°41.5990' E

Logging date: March 7, 2017

Sea floor depth (driller's): 3769 m DRF

Sea floor depth (logger's): 3770 m WRF (FMS/GPIT/EDTC-B/HNGS main run)

Total penetration: 4789 DRF (1020 m DSF) ???

Total core recovered: 150.64 m (35.3%) ???

Oldest sediment recovered: 22 Ma based on the Planktonic foraminifers

Lithology: Dark greenish to dark gray sandstone and claystone, with siltstone interbeds. Sections with low recovery assumed to be primarily composed of non-lifthified sand (618 - 761 m DSF). Dark brownish claystone with greenish to gray siltstone, calcareous–rich claystone with silt and foraminifer sandstone interbeds from 761 to 892 m DSF. Clay-rich chalk carbonate from 892 to 930 m DSF. Gray to dark gray gravel, with silty sandstone interbeds, fragmented cores recovered as pebbles/cobbles from 933 to 1081 m DSF



FMS repeat: 664-1007 m WMSF

FMS main: 662-1007 m WMSF


Magnetic declination: -2.29762°


The FMS (Formation MicroScanner) maps the conductivity of the borehole wall with a dense array of sensors. This provides a high resolution electrical image of the formation which can be displayed in either gray or color scale. The purpose of this report is to describe the images from IODP Expedition 367 and the steps used to generate them from the raw FMS measurements.


The FMS tool records electrical images using four pads, each with an array of 16 buttons, which are pressed against the borehole wall. The tool provides approximately 25% coverage of the borehole wall in a 10-inch diameter borehole. The tool string also contains a triaxial accelerometer and three flux-gate magnetometers (in the GPIT, General Purpose Inclinometry Tool) whose results are used to accurately orient and position the images. Measurements of hole size, cable speed, and natural gamma ray intensity also contribute to the processing.


Data Quality


The FMS images of hole U1499B are generally of good quality, displaying laminated or dipping beds and fractures. The larger hole size from the casing depth of 651 m WMSF to 950 m WMSF results in lower quality images. In the sections where the caliper reached its maximum reading, 3 out of 4 FMS pads still touched the borehole wall, resulting in good quality images.

For most of the logged hole interval, the images from both repeat and main passes followed approximately the same orientation.


Average heave was estimated at 0.5 m, and the heave compensator was utilized during the logging operations.


Image Processing


Processing is required to convert the electrical current in the formation, emitted by the FMS button electrodes, into a gray or color-scale image representative of the conductivity changes. This is achieved through two main processing phases: data restoration and image display.


1) Data Restoration


Speed Correction

The data from the z-axis accelerometer is used to correct the vertical position of the data for variations in the speed of the tool ('GPIT speed correction'), including 'stick and slip'. In addition, 'image-based speed correction' is also applied to the data: the principle behind this is that if the GPIT speed correction is successful, the readings from the two rows of buttons on the pads will line up, and if not, they will be offset from each other (a zigzag effect on the image).



Equalization is the process whereby the average response of all the buttons of the tool are rendered approximately the same over large intervals, to correct for various tool and borehole effects which affect individual buttons differently. These effects include differences in the gain and offset of the pre-amplification circuits associated with each button, and differences in contact with the borehole wall between buttons on a pad, and between pads.


Button Correction

If the measurements from a button are unreasonably different from its neighbors (e.g. 'dead buttons') over a particular interval, they are declared faulty, and the defective trace is replaced by traces from adjacent good buttons.


EMEX Voltage Correction.

The button response (current) is controlled by the EMEX voltage, which is applied between the button electrode and the return electrode. The EMEX voltage is regulated to keep the current response within the operating range. The button current response is divided by the EMEX voltage to give the relative conductivity of the formation.



Each of the logging runs is 'depth-matched' to a common scale by means of lining up distinctive features of the natural gamma log from each of the tool strings. If the reference logging run is not the FMS tool string, the depth shifts determined during the standard data processing are applied to the FMS images. The position of data located between picks is computed by linear interpolation. Often, for short logged intervals, a single 'block shift' is sufficient to depth-match the FMS data to the reference log. During this processing, the FMS images were depth-matched via P1AZ logs (while fine-tuned with the resistivity log) after they were depth-shifted to the sea floor (3770 m WRF).


A high-resolution conductivity log is then produced from the FMS data by averaging the conductivity values from the 64 button electrodes. This enables the FMS data to be plotted using common graphing applications and more easily used in numerical analyses (e.g. spectral analysis). Specifically, the FMS conductivity values are averaged over each of the four pads and over five 0.254-cm depth levels to produce a file with 1.27-cm sample interval containing the total (4-pad, 64-button) average conductivity value, plus the 16-button averages from each of the four pads. Note that the FMS conductivity values are un-scaled and more accurate but lower vertical resolution values of HRLA resistivity logs are not avaialable for this hole.


2) Image Display



Once the data is processed, both 'static' and 'dynamic' images are generated; the differences between these two types of image are explained below. Both types are provided online.


In 'static normalization', a histogram equalization technique is used to obtain the maximum quality image. In this technique, the resistivity range of the entire interval of good data is computed and partitioned into 256 color levels. This type of normalization is best suited for large-scale resistivity variations.


The image can be enhanced when it is desirable to highlight features in sections of the well where resistivity events are relatively subdued when compared with the overall resistivity range in the section. This enhancement is called 'dynamic normalization'. By rescaling the color intensity over a smaller interval, the contrast between adjacent resistivity levels is enhanced. It is important to note that with dynamic normalization, resistivities in two distant sections of the hole cannot be directly compared with each other. A 2-m normalization interval is used.


Oriented Presentation

The image is displayed as an unwrapped borehole cylinder. Several passes can be oriented and merged together on the same presentation to give additional borehole coverage if the tool pads followed a different track. A dipping plane in the borehole will be displayed as a sinusoid on the image; the amplitude of this sinusoid is proportional to the dip of the plane. The images are oriented with respect to north; hence the strike of dipping features can also be determined.


Interested scientists are welcome to visit the log interpretation center at LDEO if they wish to use the image generation and interpretation software.


Additional information about the drilling and logging operations can be found in the Operations and Downhole Measurements sections of the expedition report, Proceedings of the International Ocean Discovery Program, Expedition 367. For further questions about the logs, please contact:




Tanzhuo Liu

Phone: 845-365-8630

Fax: 845-365-3182

E-mail: Tanzhuo Liu


Cristina Broglia

Phone: 845-365-8343

Fax: 845-365-3182

E-mail: Cristina Broglia