Wireline Sonic Waveform Data

Science operator: Texas A&M University

Hole: U1603D

Expedition: 400

Location: Greenland Glaciated Margin

Latitude: 72° 59.0506' N

Longitude: 62° 58.8735' W

Logging date: August 31, 2023

Sea floor depth (driller's): 1811.9 m DRF

Sea floor depth (logger's): 1811.0 m WRF

Total penetration: 2245.1 m DRF (433.2 m DSF)

Total core recovered: 43.31 m (28.4 % of cored section)

Oldest sediment recovered: Early PLeistocene

Lithology: Mud; muddy sand; interlaminated to interbedded mud and sand with clasts; mud and diamicton.

ACOUSTIC TOOL USED: DSI (Dipole Sonic Imager)

Recording mode: Monopole P&S, Upper and Lower Dipole, Stoneley (all passes).

Remarks about the recording: none.

MONOPOLE P&S MODE: measures compressional and hard-rock shear slowness. The monopole transmitter is excited by a high-frequency pulse, which reproduces conditions similar to previous sonic tools.

UPPER DIPOLE MODE: measures shear wave slowness using firings of the upper dipole transmitter.

LOWER DIPOLE MODE: measures shear wave slowness using firings of the lower dipole transmitter.

STONELEY MODE: measures low-frequency Stoneley wave slowness. The monopole transmitter, driven by a low-frequency pulse, generates the Stoneley wave.

Acoustic data are recorded in DLIS format. Each of the eight waveforms generally consists of 512 samples, each recorded every 10 microseconds (monopole P&S) and 40 microseconds (dipole modes), at depth intervals of 15.24 cm (6 inches).The original waveforms in DLIS format are first loaded into Schlumberger's Techlog log analysis package. The packed waveform data files are run through a module that applies a gain correction. After being exported from Techlog they are converted into binary and GIF format (images) using in-house software. Each row of the binary file is composed of the entire waveform set recorded at each depth, preceded by the depth. In the general case of 8 waveforms with 512 samples per waveform, this corresponds to 1 + 8x512 = 4097 columns.

In this hole, the specifications of the files are:

Number of columns: 4097

Number of rows: 2703 (MSS/DSI/HRLA/HLDS/HNGS/EDTC-B main pass)

Number of rows: 649 (MSS/DSI/HRLA/HLDS/HNGS/EDTC-B repeat pass)

Number of rows: 2147 (FMS/Sonic Pass 1)

Number of rows: 2697 (FMS/Sonic Pass 2)

The following files have been loaded:

DSI from MSS/DSI/HRLA/HLDS/HNGS/EDTC-B (Main pass, pipe depth at ~50 m WMSF)
400-U1603D_mono_hrlam.bin: 0-410.9 m WMSF
400-U1603D_udip_hrlam.bin: 0-410.9 m WMSF
400-U1603D_ldip_hrlam.bin: 0-410.9 m WMSF
400-U1603D_st_hrlam.bin: 0-410.9 m WMSF

DSI from MSS/DSI/HRLA/HLDS/HNGS/EDTC-B (Repeat pass, recorded open hole)
400-U1603D_mono_hrlar.bin: 312.1-410.9 m WMSF
400-U1603D_udip_hrlar.bin: 312.1-410.9 m WMSF
400-U1603D_ldip_hrlar.bin: 312.1-410.9 m WMSF
400-U1603D_st_hrlar.bin: 312.1-410.9 m WMSF

DSI from FMS/DSI/GPIT/EDTC-B/HNGS (Pass 1, recorded open hole)
400-U1603D_mono_fms1.bin: 82.7-409.8 m WMSF
400-U1603D_udip_fms.bin: 82.7-409.8 m WMSF
400-U1603D_ldip_fms1.bin: 82.7-409.8 m WMSF
400-U1603D_st_fms1.bin: 82.7-409.8 m WMSF

DSI from FMS/DSI/GPIT/EDTC-B/HNGS (Pass 2, pipe depth at ~50 m WMSF)
400-U1603D_mono_fms2.bin: 0-409.9 m WMSF
400-U1603D_udip_fms2.bin: 0-409.9 m WMSF
400-U1603D_ldip_fms2.bin: 0-409.9 m WMSF
400-U1603D_st_fms2.bin: 0-409.9 m WMSF

All values are stored as '32 bits IEEE float'.

Any image or signal-processing program should allow to import the files and display the data.

The sonic waveform files are depth-matched to the reference run (FMS/DSI/GPIT/EDTC-B/HNGS pass 2) and depth-shifted to the seafloor (-1811.0 m). Please refer to the 'depth_matches' folder in the hole index page for the depth-matching values and to the "DEPTH SHIFT" section in the standard processing notes for further information.

NOTE: For users interested in converting the data to a format more suitable for their own purpose, a simple routine to read the binary files would include a couple of basic steps (here in old fashioned fortran 77, but would be similar in matlab or other languages):

The first step is to extract the files dimensions and specification from the header, which is the first record in each file:

  open (1, file = *.bin,access = 'direct', recl = 50) <-- NB:50 is enough to read all fields

The various fields in the header are:
      - number of depths
      - number of samples per waveform and per receiver
      - number of receivers
      - tool number (0 = DSI; 1 = SonicVISION; 2 = SonicScope; 3 = Sonic Scanner; 4 = XBAT; 5 = MCS; 6 = SDT; 7 = LSS; 8 = SST; 9 = BHC; 10 = QL40; 11 = 2PSA)
      - mode (1 = Lower Dipole, 2 = Upper Dipole, 3 = Stoneley, 4 = Monopole)
      - vertical sampling interval*
      - scaling factor for depth (1.0 = meters; 0.3048 = feet)*
      - waveform sampling rate in microseconds*

All those values are stored as 4 bytes integers, except for the ones marked by an asterisk, stored as 4 bytes IEEE floating point numbers.

Then, if the number of depths, samples per waveform/receiver, and receivers are nz, ns, and nrec, respectively, a command to open the file would be:

  open (1, file = *.bin, access = 'direct', recl = 4*(1 + nrec*ns))

Finally, a generic loop to read the data and store them in an array of dimension nrec×ns×nz would be:

Additional information about the drilling and logging operations can be found in the Operations and Downhole Measurements sections of the expedition report, Proceedings of the International Ocean Discovery Program, Expedition 400.

For any question about the data or about the LogDB database, please contact LogDB support: logdb@ldeo.columbia.edu.