Standard Wireline Data Processing
Science operator: Texas A&M University
Hole: U1613A
Expedition: 402
Location: Tyrrhenian Basin
Latitude: 40° 0.0593' N
Longitude: 10° 59.1731' E
Logging date: February 22, 2024
Sea floor depth (driller's): 2718.0 m DRF
Sea floor depth (logger's): 2720.3 m WRF
Total penetration: 2941.6 m DRF (223.6 m DSF)
Total core recovered: 99.6 m (44.6 % of cored section)
Oldest sediment recovered: Late Permian ?
Lithology: nannofossil-rich fine sand; medium sand; nannofossil ooze; oxide-rich silt and sand; conglomerate; sandy mudstone; black shale
The logging data were recorded by Schlumberger in DLIS format. Data were processed at the Borehole Research Group of Lamont-Doherty Earth Observatory in February 2024.
| Tool string |
Pass
|
Top depth (m WMSF) | Bottom depth (m WMSF) | Pipe depth (m WMSF) | Notes |
|
1. MSS/HRLA/HLDS/HNGS/EDTC-B
|
Downlog
|
0
|
200.6
|
70
|
Caliper closed. Invalid HLDS.
|
|
Uplog
|
0
|
196.6
|
70
|
|
|
| 2. DSI/EDTC-B |
Downlog
|
0
|
179.9
|
70
|
|
|
Uplog
|
0
|
182.1
|
70
|
|
After the completion of coring operations, the triple combo (MSS/HRLA/HLDS/HNGS/EDTC-B) and sonic (DSI/EDTC-B) tool strings were run in turn for downlog and uplog. The triple combo downlog was run with the caliper closed and the radioactive source turned off, thus resulting in invalid HLDS data for this pass.
Sea condition was calm and the heave was low (0 m), so the Wireline Heave Compensator (WHC) was not used during the entire logging operation of this hole.
The depths in the table are for the processed logs (after depth matching between passes and depth shift to the sea floor). Discrepancies may exist between the sea floor depths determined from the downhole logs and those determined by the drillers from the pipe length. Typical reasons for the depth discrepancies are ship heave, wireline and pipe stretch, tides, and the difficulty of getting an accurate sea floor from a 'bottom felt' depth in soft sediment.
Depth match and depth shift to sea floor. The original logs of the tool strings were depth-matched using the gamma ray curve of the triple combo uplog as a depth reference.
Depth matching is typically done in the following way. One log is chosen as reference (base) log (usually the total gamma ray log from the run with the greatest vertical extent and no sudden changes in cable speed), and then the features in the equivalent logs from the other runs are matched to it in turn. This matching is performed manually. The depth adjustments required to bring the match log in line with the base log are then applied to all the other logs from the same tool string.
The depth-matched logs were then shifted to the sea floor. The sea floor depth was determined by the step in gamma ray values at 2720.30 m WRF observed on the triple combo uplog. This value differs by 2.3 m from the sea floor depth given by the drillers (see above).
Environmental corrections. The HRLA and HLDS logs were corrected for hole size during the recording.
High-resolution data. Bulk density (HLDS) data were recorded at a sampling rate of 2.54 cm, in addition to the standard sampling rate of 15.24 cm. The enhanced bulk density curve is the result of Schlumberger enhanced processing technique performed on the MAXIS system onboard. While in normal processing short-spacing data are smoothed to match the long-spacing one, in enhanced processing this is reversed. In a situation where there is good contact between the HLDS pad and the borehole wall (low-density correction) the results are improved, because the short spacing has better vertical resolution. Gamma ray data from the EDTC-B tool were recorded at sampling rates of 5.08 and 15.24 cm. The HRLA data were also acquired every 5.08 cm; in the database they were resampled at 15.24 cm, for ease of comparison with the other logs.
Acoustic data. The dipole shear sonic imager (DSI) was operated in low frequency mode for the lower dipole and standard mode for the upper dipole, P&S monopole, and Stoneley. The sonic velocities were computed from the sonic slowness. Due to the poor labeling of the DTCO logs, the sonic data were reprocessed at LDEO.
The quality of the data is assessed by checking against reasonable values for the logged lithologies, by repeatability between different passes of the same tool, and by correspondence between logs affected by the same formation property (e.g., the resistivity log should show similar features to the sonic velocity log).
Gamma ray logs recorded through bottom hole assembly (BHA) and drill pipe should be used only qualitatively, because of the attenuation of the incoming signal. The thick-walled BHA attenuates the signal more than the thinner-walled drill pipe.
A wide (>12") and/or irregular borehole affects most recordings, particularly those that require eccentralization and a good contact with the borehole wall (HLDS). Hole diameter was recorded by the hydraulic caliper on the HLDS tool. For U1613A, the near-bit caliper measurement indicated that hole was in-gauge from 148 m WMSF to TD. The hole size became quite large (12-17") with numerous washouts above this depth level. As a result, log data such as gamma ray and density from the upper part of the logged hole section (87-148 m WMSF) should be used with caution.
A Null value of -999.25 may replace invalid log values.
Additional information about the drilling and logging operations can be found in the Operations and Downhole Measurements sections of the expedition report, Proceedings of the International Ocean Discovery Program, Expedition 402.
For any question about the data or about the LogDB database, please contact LogDB support: logdb@ldeo.columbia.edu.