Wireline Standard Data Processing

ODP logging contractor: LDEO-BRG

Well name: 642E

Leg: 104

Location: Voring Plateau (Norwegian Sea)

Latitude: 67° 13.2' N

Longitude: 2° 55.8' E

Logging date: July, 1985

Bottom felt: 1289 mbrf (used for depth shift to sea floor)

Total penetration: 1229.4 mbsf

Total core recovered: 372.6 m (41.1 %)

Logging Runs

Logging string 1: DIT/LSS/GR

Logging string 2: LDT/CNTG/NGT

Logging string 3: BHTV

No information available about use of wireline heave compensator. Ship heave was less than 0.5 m.

Casing

The following casing depths are as they appear on the logs after differential depth shift (see 'Depth shift' section) and depth shift to the sea floor. As such, there might be a discrepancy with the original depths given by the drillers onboard. Possible reasons for depth discrepancies are ship heave, lack of wireline heave compensator, and drill string and/or wireline stretch.

DIT/LSS/GR: Casing at ~372.5 mbsf

LDT/CNTG/NGT: Casing at ~372.5 mbsf.

Processing

Depth shift: Original logs have been interactively depth shifted with reference to NGT from LDT/CNTG/NGT run and to the sea floor (- 1289 m). The program used is an interactive, graphical depth-match program, which allows to visually correlate logs and to define appropriate shifts. The reference and match channels are displayed on the screen, with vectors connecting old (reference curve) and new (match curve) shift depths. The total gamma ray curve (SGR) from the NGT tool run on each logging string is used to correlate the logging runs most often. In general, the reference curve is chosen on the basis of constant, low cable tension and high cable speed (tools run at faster speeds are less likely to stick and are less susceptible to data degradation caused by ship heave). Other factors, however, such as the length of the logged interval, the presence of drill pipe, and the statistical quality of the collected data (better statistics is obtained at lower logging speeds) are also considered in the selection. A list of the amount of differential depth shifts applied at this hole is available upon request.

Gamma-ray processing: NGT data have been processed to correct for borehole size and type of drilling fluid.

Acoustic data processing: The long-spacing sonic logs have been processed to eliminate some of the noise and cycle skipping experienced during the recording. Using two sets of the four transit time measurements and proper depth justification, four independent measurements over a -2ft interval centered on the depth of interest are determined, each based on the difference between a pair of transmitters and receivers. The program discards any transit time that is negative or falls outside a range of meaningful values selected by the processor.

Quality Control

null value=-999.25. This value generally appears in discrete core measurement files and also it may replace recorded log values or results which are considered invalid (ex. processed sonic data).

During the processing, quality control of the data is mainly performed by cross-correlation of all logging data. Large (>12") and/or irregular borehole affects most recordings, particularly those that require eccentralization (CNTG, LDT) and a good contact with the borehole wall. Both density and neutron data recorded are of excellent quality.

Data recorded through casing, such as the NGT and CNTG data above 72.5 mbsf, should be used qualitatively only because of the attenuation on the incoming signal.

Hole diameter was recorded by the 3-arm mechanical caliper.

The DIT/LSS/GR data was originally subdivided into several files; as overlap existed between files, the data has been spliced as follows:

resistivity: spliced at 470, 685, and 900 mbsf

gamma ray: spliced at 373, 457.5 680, and 900 mbsf. The uppermost interval, from 152 to 250 mbsf through casing, has not been spliced because the little overlap does not allow a proper depth correlation.

acoustic slowness and velocity: spliced at 460, 675, and 895 mbsf

caliper: spliced at 460, 680, and 895 mbsf.

No merging necessary for LDT/CNTG/NGT data.

Additional information about the logs can be found in the 'Explanatory Notes' and Site Chapter, ODP IR volume 104. For further questions about the logs, please contact:

Cristina Broglia
Phone: 845-365-8343
Fax: 845-365-3182
E-mail: Cristina Broglia